AUTOLINE C570
|
|
$289.79
Price
|
$150.00
Core
|
+ Sold in packs of 1x1
Pack
|
$439.79
Total
|
|
|
|
|
|
- All base, body and air horns are stamped prior to disassembly to ensure units are reassembled with the
proper “companion” parts. Internal parts such as jets and metering rods are identified, to insure they
remain with the original castings, where variations may have occurred at the manufacturing level. This process ensures
that original flow characteristics are maintained.
- After disassembly all parts are inspected and cleaned in
industrial equipment. Internal parts such as gaskets, needle and seats and plunger cups are discarded. All white metal
castings are chemically processed to restore the factory finish. All aluminium castings are sandblasted or tumbler
processed to restore the finish. Bases are surfaced to ensure proper mating with the body assembly and the manifold.
Mounting holes are refaced to assure proper torque of mounting fasteners.
- During our sub-assembly process
all threads, inlets and vacuum pipes are inspected and repaired or replaced if necessary. Throttle and choke plates
are inspected and replaced if not serviceable. Throttle bushings are installed wherever throttle shaft play is not within
tolerances. Completed base assemblies are checked for vacuum integrity. Any base that does not meet our specifications
must be repaired prior to use.
- Throughout our assembly process all body and calibration components are reassembled
to the original unit to maintain product calibration. All assembly components are tested prior to product assembly.
- Completed product is flow tested throughout all ranges of operation to ensure proper calibration. Choke adjustment,
idle speed and air-screw settings are made during product testing. This process allows the technician to start the vehicle
upon product installation. Final adjustments may be necessary due to varied engine condition.
- All AutoLine
Carburetors are heat shrink packaged with installation instructions, mounting gaskets and specific technical bulletins.
Important Install Notice: Satisfactory performance cannot be obtained from the spread bore unless the correct gasket
is used between the carburetor and intake manifold. Certain original equipment spread bore manifolds have and exhaust crossover
track. This consists of two holes ( approx. 3/8 diameter) beside the primary bores (smaller bores).
If your manifold has the exhaust crossover slots, prepare for the installation as follows:
- Install the asbestos gasket supplied with the carburetor.
- Place the stainless steel plate originally supplied with vehicle on the top of the asbestos gasket.
- Mount the carburetor on top of the stainless steel plate with no additional gasket between the plate and the carburetor.
![](/Images/MoreInfo/install.png) Prevent Carburetor Flooding / Premature Failure! - Avoid fuel blends containing high levels of ethanol. Refer to your Owners Manual for fuel requirements.
- Ethanol may loosen and dislodge debris from the fuel tank, fuel lines and other fuel system components not originally designed for ethanol mixtures.
- Always replace the Fuel Filter and flush the fuel lines when replacing or servicing the carburetor.
- Dirt and debris from unfiltered fuel can catch between the inlet valve and seat, leading to flooding.
- Consider adding Fuel Stabilizer to the fuel tank if the vehicle won't be driven for extended periods of time.
- Fuel stabilizer prevents gas from evaporating and/or forming sticky resins that can clog the carburetor.
![](/Images/MoreInfo/doc.png) Additional Resources Autoline Warranty & Core Return Details - Carburetors
![](/Images/MoreInfo/support.png) Autoline Technical Support If you are having trouble choosing the correct AutoLine part, or experiencing issues during or after installation of this part, AutoLine's ASE Certified Technicians are available to help answer your questions.
📧 Email: tech@autoline.ca
Attention California Customers - Warning: This product can expose you to chemicals including lead and mineral oils which are known to the State of California to cause cancer or birth defects or other reproductive harm. For more information, visit www.P65Warnings.ca.gov
|
OEM / Interchange Numbers: 3633S, 3665S, C4AFB |
AUTOLINE Warranty Information:Throttle Bodies & Distributors 12 months. Fuel Injectors & Diesel Products 24 months. Carburetors 90 days.Warranty Details |
|