MAHLE / CLEVITE MS829V
|
|
$113.79
Price
|
$0.00
Core
|
+ Sold in packs of 1x1
Pack
|
$113.79
Total
|
|
(Size: 0.001" Undersize)
|
|
|
|
High Performance; Set; V Series (Tri-Metal/Lead-Indium Overlay) |
V-Series rod bearings typically have low to medium eccentricity and a hardened steel
back. All V-Series main sets use a single piece thrust bearing rather than the former Vandervell assembled type of construction. V-Series bearings do not have flash plating on the steel back. The chief difference between the V-Series and other Clevite® TriMetal™ bearings is the use of a lead-indium overlay.
Use V-Series bearings if
prior experience has shown a preference for the lead-indium type of overlay. Lead-indium overlay offers somewhat better conformability than lead-tin-copper overlay with slightly reduced wear resistance.
Clevite® TriMetal™ engine bearings have been the industry standard since the first patent on the cast, copper, lead composition decades ago. These points are just a few of the advantages Clevite's TriMetal™ engine bearings:- Seizure Resistance - Clevite TriMetal™ bearings have as much as 40% better seizure resistance than competitors' engine bearings.
- Load Capacity - Clevite TriMetal™ bearings can withstand over 60% higher loads for extended periods compared to competitor bearings.
- Embedability & Conformability - The overlay on a TriMetal™ bearing offers a superior surface for forgiveness, offering additional protection that can be extremely beneficial in an engine that is poorly maintained.
- Durability - Clevite TriMetal™ bearings not only exceed light vehicle OE durability requirements of 150,000 miles, they also exceed heavy vehicle OE durability requirements of 300,000 miles.
- Even all tri-metal engine bearings are not the same. If you want the highest quality, strongest, and original TriMetal™ bearings, ask for Clevite Engine Bearings.
The letters at the end of each part number indicate a specific feature of the part.
Example:
Part #CB1234HXNK: H = High Performance, X = .001" more oil clearance than standard, N = Narrowed for greater crankshaft fillet clearance, K = TriArmor™ coating applied to the bearing surface.
Letters & Their Meanings | A Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material. | M Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. | AL Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material. | N Narrowed for greater crankshaft fillet clearance. | B Steel backed bearings with a conventional babbit lining. | P Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. | C Steel backed bearings with a copper-lead lining. | R Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. | D Bearing has dowel hole. | S Indicates a set number designation. | G Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable. | V High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. | H High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load. | VG High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. | HG High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load. | X Bearing has .001” more oil clearance than standard. | HT High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load. | XX Bearing has .002” more oil clearance than standard. | K TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines. | W Indicates a part that is a thrust washer (may also be designated upper or lower). |
![](/Images/MoreInfo/doc.png) Additional Resources Engine Bearing Failure Analysis and Correction
|
MAHLE / CLEVITE Warranty Information:12 Months |
|