|
MAHLE / CLEVITE CB663VXN
|
|
$12.39
Price
|
$0.00
Core
|
+ Sold in packs of 1x1
Pack
|
$12.39
Total
|
|
|
(Size: Standard)
|
|
|
| MAHLE / CLEVITE CB663VXN Specifications |
|---|
| Min Shaft | Max Shaft | Min Oil | Max Oil | Max Wall | Min Bore | Max Bore | Max Length | | 2.099 | 2.1 | 0.0018 | 0.0038 | 0.0616 | 2.2247 | 2.2252 | 0.792 |
|
|
| High Performance; V Series (Tri-Metal/Lead-Indium Overlay); Pair |
V-Series rod bearings typically have low to medium eccentricity and a hardened steel
back. All V-Series main sets use a single piece thrust bearing rather than the former Vandervell assembled type of construction. V-Series bearings do not have flash plating on the steel back. The chief difference between the V-Series and other Clevite® TriMetal™ bearings is the use of a lead-indium overlay.
Use V-Series bearings if
prior experience has shown a preference for the lead-indium type of overlay. Lead-indium overlay offers somewhat better conformability than lead-tin-copper overlay with slightly reduced wear resistance.
Clevite® TriMetal™ engine bearings have been the industry standard since the first patent on the cast, copper, lead composition decades ago. These points are just a few of the advantages Clevite's TriMetal™ engine bearings:- Seizure Resistance - Clevite TriMetal™ bearings have as much as 40% better seizure resistance than competitors' engine bearings.
- Load Capacity - Clevite TriMetal™ bearings can withstand over 60% higher loads for extended periods compared to competitor bearings.
- Embedability & Conformability - The overlay on a TriMetal™ bearing offers a superior surface for forgiveness, offering additional protection that can be extremely beneficial in an engine that is poorly maintained.
- Durability - Clevite TriMetal™ bearings not only exceed light vehicle OE durability requirements of 150,000 miles, they also exceed heavy vehicle OE durability requirements of 300,000 miles.
- Even all tri-metal engine bearings are not the same. If you want the highest quality, strongest, and original TriMetal™ bearings, ask for Clevite Engine Bearings.
The letters at the end of each part number indicate a specific feature of the part.
Example:
Part #CB1234HXNK: H = High Performance, X = .001" more oil clearance than standard, N = Narrowed for greater crankshaft fillet clearance, K = TriArmor™ coating applied to the bearing surface.
| Letters & Their Meanings | A
Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material. | M
Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. | AL
Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material. | N
Narrowed for greater crankshaft fillet clearance. | B
Steel backed bearings with a conventional babbit lining. | P
Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. | C
Steel backed bearings with a copper-lead lining. | R
Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. | D
Bearing has dowel hole. | S
Indicates a set number designation. | G
Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable. | V
High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. | H
High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load. | VG
High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. | HG
High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load. | X
Bearing has .001” more oil clearance than standard. | HT
High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load. | XX
Bearing has .002” more oil clearance than standard. | K
TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines. | W
Indicates a part that is a thrust washer (may also be designated upper or lower). |
 Additional Resources
Engine Bearing Failure Analysis and Correction
|
MAHLE / CLEVITE Warranty Information:12 Months |
|
