All base, body and air horns are stamped prior to disassembly to ensure units are reassembled with the
proper “companion” parts. Internal parts such as jets and metering rods are identified, to ensure they
remain with the original castings, where variations may have occurred at the manufacturing level. This process ensures
that original flow characteristics are maintained.
After disassembly all parts are inspected and cleaned in
industrial equipment. Internal parts such as gaskets, needle and seats and plunger cups are discarded. All white metal
castings are chemically processed to restore the factory finish. All aluminium castings are sandblasted or tumbler
processed to restore the finish. Bases are surfaced to ensure proper mating with the body assembly and the manifold.
Mounting holes are refaced to assure proper torque of mounting fasteners.
During the sub-assembly process
all threads, inlets and vacuum pipes are inspected and repaired or replaced if necessary. Throttle and choke plates
are inspected and replaced if not serviceable. Throttle bushings are installed wherever throttle shaft play is not within
tolerances. Completed base assemblies are checked for vacuum integrity. Any base that does not meet specifications
must be repaired prior to use.
Throughout the assembly process all body and calibration components are reassembled
to the original unit to maintain product calibration. All assembly components are tested prior to product assembly.
Completed product is flow tested throughout all ranges of operation to ensure proper calibration. Choke adjustment,
idle speed and air-screw settings are made during product testing. This process allows the technician to start the vehicle
upon product installation. Final adjustments may be necessary due to varied engine condition.
All Autoline
Carburetors are heat shrink packaged with installation instructions, mounting gaskets and specific technical bulletins.
Important Install Notice: Carburetors with climatic control choke having a binding or stuck choke valve should be checked
for a burnt out heater tube located in the exhaust manifold. This is not visible from the outside of the carburetor, but can be checked
by removing the climatic choke cover. Whenever carbon deposits are found inside the choke housing, a burnt out heater tube in the manifold
is indicated.
Replacing the carburetor is not a correction as the burnt out heater tube will continue to damage carburetors.
Correct procedure is to replace the burnt out heater tube.
Empêcher l'inondation du carburateur / la défaillance prématurée !
Évitez les mélanges de carburant contenant des niveaux élevés d'éthanol. Référez à votre manuel d'utilisation pour les exigences en matière de carburant.
L'éthanol peut détacher et déloger les débris du réservoir de carburant, des canalisations de carburant et d'autres composants du système d'alimentation qui n'ont pas été conçus à l'origine pour des mélanges d'éthanol.
Remplacez toujours le filtre à carburant et rincez les canalisations de carburant en remplaçant ou entretenant le carburateur.
Les saletés et les débris du carburant non filtré peut se loger entre la soupape et le siège d'admission, entraînant des inondations.
Considérez ajouter du Stabilisateur de Carburant au réservoir de carburant si le véhicule ne sera pas conduit pendant de longues périodes de temps.
Un stabilisateur de carburant empêche le gaz de s'évaporer et/ou de former des résines collantes qui peuvent boucher le carburateur.
Si vous avez des difficultés en choisissant la bonne pièce Autoline, ou avez des problèmes pendant ou après l'installation de cette pièce, les techniciens Autoline certifiés ASE sont disponibles pour aider avec vos questions.
Attention aux clients en Californie - ATTENTION : Ce produit peut vous exposer aux produits chimiques y compris le plomb et les huiles minérales qui sont connus par l'État de Californie de causer le cancer ou les anomalies congénitales ou d'autres troubles de la reproduction. Pour plus d'informations, visitez www.P65Warnings.ca.gov
AUTOLINE Informations sur la garantie:Corps de papillon et distributeurs 12 mois. Injecteurs de carburant et produits diesel 24 mois. Carburateurs 90 jours.Détails de la garantie