|
GM GENUINE MU1657
|
|
$253.79
Price
|
$0.00
Core
|
+ Sold in packs of 1x1
Pack
|
$253.79
Total
|
|
|
|
|
|
| The float arm (where pictured) may ship detached to prevent damage in transit. To connect, simply snap the wire end into the sender hole. |
| GM GENUINE MU1657 Specifications |
|---|
| Connector Gender | Female | | Connector Shape | Oval | | Depth (IN) | 7.24 | | Depth (MM) | 184 | | Fuel Sending Unit Included | Yes | | Fuel Tank Pressure Sensor Included | Yes | | Fuel Type | Gas | | Gasket or Seal Included | Yes | | Gasket Or Seal Material | Rubber | | Inlet Outside Diameter (IN) | 0.37 | | Inlet Outside Diameter (MM) | 9.49 | | Inlet Type | Quick Connect | | Internal Or External Strainer | Internal | | Lock Ring Included | No | | Mounting Hardware Included | No | | Outlet Outside Diameter (IN) | 0.62 | | Outlet Outside Diameter (MM) | 15.82 | | Outlet Quantity | 1 | | Outlet Type | Quick Connect | | Pump Type | Electric | | Strainer Included | Yes | | Tank Seal Outside Diameter (in) | 5.8 | | Tank Seal Outside Diameter (mm) | 147.33 | | Tank Seal Rim Shape | Round | | Tank Seal Thickness (in) | 0.23 | | Tank Seal Thickness (mm) | 5.96 | | Terminal Gender | Male | | Terminal Quantity | 7 | | Terminal Type | Blade Pin | | Voltage | 12 vDC | | Volume (cu in) | 1395.98cu in | | Wire Colors | Multiple | | Wire Harness Included | Yes |
|
|
ACDelco GM Original Equipment Fuel Pump Modules consist of an electric fuel pump and a jet pump. The jet pump maintains a consistent fuel level inside the internal fuel pump reservoir. These assemblies are equipped with quiet Generation 4 turbine pumps with integral strainer socks. These original equipment fuel pump modules have been manufactured to fit your specific GM vehicle, providing the same performance, durability, and service life you expect from General Motors .
Features
- Designed with guide rods to retain proper alignment while reducing pinching
- Include a reservoir and jet pump to prevent fuel pump starvation when the fuel level is low
- Strainer is placed inside the module to help reduce the chance of puncture
- Acetyl plastic for good high-alcohol fuel tolerance
- Electrical connections are designed to help eliminate below-cover burning due to vehicle vibration
- GM-recommended replacement part for your GM vehicle's original factory component
- Offering the quality, reliability, and durability of GM OE
- Manufactured to GM OE specification for fit, form, and function
 Benefits of Purchasing a Fuel Pump & Housing Assembly Purchasing just the fuel pump is less expensive up-front, but a complete Fuel Pump & Housing Assembly provides added benefits:
- Extend Service Life: New strainer(s), hoses, sensors and other components help resolve problems that could be caused by more than just the pump.
- Reduce Install Time: Since you don't have to disassemble the housing, which could lead to damage, replacement becomes a simple swap, dramatically reducing installation time.
- Save Money: The cost of the assembly is often cheaper than buying the components individually, and means you only have to do the job once.
 Prevent Premature Fuel Pump Failure Preventing premature fuel pump failure is far less expensive and time consuming than continuing to replace the pump. There are three common causes for premature fuel pump failure:
| ELECTRICAL ISSUES |
Poor electrical connections will mimic symptoms of a failed pump, sometimes resulting in unnecessary replacement. Before replacing the pump:
- Use a Fuel System Tester to test pump pressure is within expected range
- Use an Electrical Tester to test for bad wiring, burnt or corroded connectors
- Check / Replace faulty Fuse(s) and Relay
BEFORE REPLACEMENT |
| FUEL CONTAMINATION |
Dirt, rust or debris in the fuel can clog strainers and stick to internal pump components. When replacing the pump:
- Replace Fuel Filter or Fuel Strainer
- Empty and clean the tank with Fuel Tank Cleaner
- Fill tank with fresh, uncontaminated fuel of appropriate grade
DURING REPLACEMENT |
| PUMP DAMAGE / OVERHEATING |
Running low on gas causes your fuel to heat up quicker, and your pump to work harder. After replacing the pump:
- Maintain at least 1/4 tank of fuel and use a Fuel Additive / Conditioner to keep pump cool and lubricated
- If vehicle is stored without use, drain tank to prevent pump corrosion from fuel oxidation
AFTER REPLACEMENT |
|
| OEM / Interchange Numbers: 19207718, 19256622, 88983269, MU1205, MU1352, MU1546 |
Warranty Information:Limited Lifetime |
|
